RoadEng, Terrain Tools
Version
7.0.10.0
Softree Technical Systems Inc.
604-519-6222
866-519-6222
mail@softree.com
www.softree.com
-INTRODUCTION
-HARDWARE PROTECTION KEY AND PASSWORD
-COMPATIBILITY WITH PREVIOUS VERSIONS
-ENHANCEMENTS SINCE THE PREVIOUS RELEASE
-BUG FIXES SINCE THE PREVIOUS RELEASE
Please see our web site (support.softree.com
) for up to date
Version 7.x is file compatible with versions 6.x, 5.x
and 4.x. Although earlier versions will read newer version files,
data associated with newer features will not be visible in earlier versions
and will be lost if the file is saved in the earlier version..
There is no need to uninstall previous versions before installing 7. If
you wish to return to an earlier version, just install it over. If you
choose to uninstall a previous version, you may want to first back up your
defaults and layouts (files in the RoadEng folder).
Only versions 5.x and 4.x have a conversion utility that allows them to read
version 3.x files and these conversion utilities are incompatible with
64bit operating systems. Please contact
Softree
to convert 3.x files.
Once files have been converted, they can no longer
be read by 3.x software. There is no "Save As previous version" function,
although ASCII and DXF formats can be used for this purpose to some extent.
The following features have been added to Softree products since the version 6.0 release March, 2013. This is when 6.1β was created.
The
version number below is the first version of the software that contains the
enhancement.
|
Version |
Module |
Description |
| 6.1.00.0 | Terrain | DWG libraries updated |
| 6.1.00.0 | All | Grid (Plan, Profile, Section) support for decimals. |
| 6.1.00.0 | Location | Vertical alignment optimization added. |
| 6.1.00.0 | Terrain | Seperate colors and feature names added for grading slope lines |
| 6.1.01.0 | Softree Opt | New algorithm added: Continuous with Tangents v2 (see new example). Discrete algorithm removed. |
| 6.1.01.0 | Softree Opt | Document and example files updated. (C:\Users\Public\Documents\softree\roadeng\Data\Samples) |
| 6.1.01.1 | Softree Opt | Option to omit insert of curve boundary at control point. |
| 6.1.01.1 | Softree Opt | Movement costs: added maximum grade value (to prevent uphill push) |
| 6.1.01.1 | Softree Opt | New calculation method added: Use Network Model in advanced options tab |
| 6.1.01.1 | Softree Opt | Curve constraints: Sag/Crest independent K values |
| 6.1.01.1 | Location | Next/Prev Stn Buttons in Template Editor |
| 6.1.01.1 | Terrain | Speed Improvements in Terrain Points and Features window |
| 6.1.01.1 | Terrain | Feature Selection by Crossing Breakline Property |
| 6.1.01.1 | All | Measure Tool Improvements (additional info, add function to Template Editor). |
| 6.1.02.0 | Location | Currency: allow user to set desired currency in Module-Setup ($, Pounds, Euros, etc.) |
| 6.1.02.0 | Softree Opt | Control points/pits, allow station="start" or "end" as option (in case user changes length of alignment). |
| 6.1.02.0 | Softree Opt | Maximum non-pit haul distance added |
| 6.1.02.0 | Softree Opt | Panel alignments list: add shift up/down |
| 6.1.02.0 | Softree Opt | Status area: items added, modified. |
| 6.1.03.0 | Location | LandXML multiple profiles: can now choose from list. |
| 6.1.03.0 | Softree Opt | Add new profile sub-view for earth movement (haul) visualization (not complete) |
| 6.1.03.0 | Softree Opt | Allow pits to have required borrow waste (Source, Sink) volumes to simulate saving/using material for/from outside sources (i.e. other alignments) |
| 6.1.03.0 | Softree Opt | Balance line display (added to Alignment display options) |
| 6.1.03.0 | Softree Opt | Control points display option (added to Alignment display options) |
| 6.1.03.0 | Softree Opt | Haul cost (in Ground Types table) freehaul and overhaul distances now calculated from costs (see F1 help) |
| 6.1.03.0 | Softree Opt | Set current now merges alignment with existing (instead of deleting vertical alignment outside of range) |
| 6.1.03.0 | Softree Opt | Statistics output: average haul, etc. (set Export Mass Movement check box in options Advanced tab - then look in folder on hard drive with same name as document) |
| 6.1.03.0 | Softree Opt | UI to allow user to set pit elevation (if different from station) |
| 6.1.03.0 | Softree Opt | Vertical band limits alignment? Warn user! |
| 6.1.03.1 | Softree Opt | Add fixed interval to General tab, points selection (independent of point selection list) |
| 6.1.03.1 | Softree Opt | Custom labels: attributes added. |
| 6.1.03.1 | Softree Opt | Labels for accumulated slope distance added. |
| 6.1.03.1 | Softree Opt | Haul display in Profile sub-views mostly finished. |
| 6.1.03.1 | Softree Opt | Statistics added to output area - beta. |
| 6.1.03.5 | Softree Opt | Vertical band graphic modified to include other constraints. |
| 6.1.03.5 | Softree Opt | New costraints added: Overland, Full bench cut, Side-cast |
| 6.1.03.5 | Softree Opt | Polyline option added (no vertical curves) |
| 6.1.03.5 | Softree Opt | Haul graphic improved and haul data export to file added. |
| 6.1.04.0 | Softree Opt | Current optimized alignment items always displayed in Profile (in magenta) when selected. |
| 6.1.04.0 | Softree Opt | New user interface for selecting haul costs . |
| 6.1.04.0 | Softree Opt | Vertical Band display enhanced to show before optimization. |
| 6.1.04.0 | Softree Opt | More Special constraints added. |
| 6.1.04.0 | Softree Opt | Profile window hover tooltip shows information about current optimized alignment. |
| 6.1.04.0 | Softree Opt | Two solver options added to work around errors (Alignment tab). |
| 6.1.04.0 | Softree Opt | R-Cost available for optimized alignments and current alignment. |
| 6.1.04.0 | Softree Opt | File-Save-As Haul Table improved. |
| 6.1.04.0 | Softree Opt | Features added to keep the assigned Borrow/Waste amounts up to date with the current allignment cost pit quantities. |
| 6.1.04.2 | Location | Pipe bend angle labels added. |
| 6.1.04.2 | Location, Terrain | Multi-Plot sub-view item locking added. |
| 6.1.04.3 | Location | Multi-Plot option to display extra leading zeros in page numbers. No user interface yet; set PageFormatCharacters in Softree.ini (usually C:\ProgramData\Softree\RoadEng\softtree.ini). |
| 6.1.04.4 | Softree Opt | Allow copy of results table to clipboard (right click menu) |
| 6.1.04.4 | Softree Opt | Grade exclusion range for tangents. For example -8.0% < grade < -0.5% and 0.5% < grade < 8.0%. |
| 6.1.04.4 | Softree Opt | Help for errors/warnings. |
| 6.1.04.6 | All | 3D Window speed improvements (beta) set OpenGLflag=1 in your C:\ProgramData\Softree\RoadEng\softree.ini file. This may limit the maximum number of points that can be triangulated. |
| 6.1.04.7 | Location | Turn off fast draping option added to Module-Setup, Alignment tab (allows use of sub-horizon surfaces that do not cross the centerline). |
| 6.1.04.7 | Softree Opt | Results Log added to optimization options. |
| 6.1.04.8 | Location | DWG, DGN export: moved station range into main dialog box. Now Multi-Plot export is filtered by station range too. |
| 6.1.04.9 | Terrain | Mouse Rotate in Move/Size mode (plan, profile windows). |
| 6.1.04.9 | Softree Opt | Right Click in panel to copy haul report to clipboard. |
| 6.1.06.0 | Location | Compound ground types added. |
| 6.1.06.0 | Terrain/Location | 3D Window:Transparency available for surface representaion (use extended color editor). |
| 6.1.06.0 | Terrain | 3D Window: tooltips added, line display enhanced, redraw on selection change, background options added to Options. |
| 6.1.06.0 | Terrain | 3D Window: selection of features now possible. |
| 6.1.06.0 | Softree Opt | Min curve length and min tangent length independent (Variable Curves and Tangents). |
| 6.1.06.0 | Softree Opt | Option added to allow optimization using existing curve locations (Tangent/curve boundaries at current profile). |
| 6.1.06.0 | Softree Opt | User control of summary list contents added. |
| 6.1.06.0 | Softree Opt | Pit open cost added. |
| 6.1.06.0 | Softree Opt | Constraints display added before Optimization; option top "soften" constraints added. Softening constraints will usually find a solution to a previously infeasable problem and provide feedback as to the infeasable constraint. |
| 6.1.06.1 | Softree Opt | Current alignment is now part of the vertical alignments list. |
| 6.1.06.2 | All | 3D window improvements. |
| 6.1.06.2 | Location | 3D options menu has a dialog that allow users to control what is exported to 3D window. |
| 6.1.06.2 | Location | Changed alignment data structure to enable faster 3D update and other future speed improvements. Uses more memory - softree.ini flag to disable. Beta! |
| 6.1.06.2 | Terrain | Simplify function changed to include smoothing. |
| 6.1.06.2 | Terrain | 3D drivethrough enhanced. |
| 6.1.06.2 | Terrain | 3D display of non-surface points (point cloud) enhanced (beta). |
| 6.1.06.2 | Softree Opt | Compare checkbox added to Alignments panel - comparison between current and selected alignment now uses columns. |
| 6.1.06.2 | Softree Opt | Items for display enhanced, more to come. |
| 6.1.06.3 | All | New Ground Table item defaults to selected (costs too) |
| 6.1.06.3 | Softree Opt | Allow multiple vertical alignments and comparison for RoadEng users. |
| 6.1.06.5 | Softree Opt | Add optimality gap to avaiable list items. |
| 6.1.06.5 | Softree Opt | Geometric feasability tester added (beta). |
| 6.1.06.5 | Location | Ground editor: Indicate if ground type is used. |
| 6.1.06.5 | Softree Opt | Items added optimization display list including optimization time stamp. |
| 6.1.06.5 | Softree Opt | Re-cost now always uses same points as other RoadEng volumes; Mass Hual and overflow/underflow should always match. |
| 6.1.06.5 | Softree Opt | Pits tab: Modify Station button added (double click works too). |
| 6.1.07.0 | Softree Opt | Check for conflicts in constraints added to Optimizer Options dialogue box. |
| 6.1.07.0 | Softree Opt | Document updated. |
| 7.0.00.0 | All | Non-Beta release. |
| 7.0.00.0 | All | Runs on WinXP. |
| 7.0.00.0 | Softree Opt | Side-cast subtractred from Mass Haul. |
| 7.0.00.0 | Softree Opt | Haul graph output file - option to aggregate station ranges. |
| 7.0.00.0 | Softree Opt | Add "pit borrow" and "pit waste" to the information list available items. |
| 7.0.00.0 | Softree Opt | Quick Profile added: creates a smoothed ground line based on optimizer constraints and standards - available to RoadEng licenses. |
| 7.0.00.0 | Softree Opt | "User defined" alignment specification added to Standards: keeps current alignment VIP and curve locations (preserves curve length) during optimization. |
| 7.0.00.1 | Loction | Pits dialogue box replaces old Borrow/Waste assignments. |
| 7.0.00.1 | Loction | Re-Cost check box added to Recalculate all dialogue box. |
| 7.0.00.1 | Loction | Mass Haul, Optimal haul graphics, show faded (washed out) if out of date. |
| 7.0.00.1 | Loction | Profile graphics show faded (washed out) if another alignment is selected in the Alignment panel. |
| 7.0.00.3 | Terrain | Grading: basic templates enabled (beta - not suitable for inside corners). |
| 7.0.00.3 | Softree Opt. | Profile hover tip (tooltip) improved to include pits and other items. |
| 7.0.00.3 | Softree Opt. | Tutorial and help files updated. |
| 7.0.00.9 | Location | Multi-Plot allows more than one Profile sub-view; added pagination to deal with two or more Profiles per page. |
| 7.0.01.0 | Softree Opt. | Tolerances added to Module-Setup, units tab. Used for ignoring small constraint violations in Softree Optimal. |
| 7.0.01.0 | Softree Opt. | Auto station ranges based on side slope for a) Full bench cut constraint b) Min cut depth constraint c) Side-cast constraint. |
| 7.0.01.0 | Softree Opt. | Auto station ranges based on average ground line grade for haul direction constraint. |
| 7.0.01.0 | Softree Opt. | Enhancements to Alignments panel tree display. |
| 7.0.01.0 | Softree Opt. | Optional constraints violations check in re-cost. This allows you to see quickly if a design is within standards. |
| 7.0.01.0 | Softree Opt. | Constraints display in Profile more informative (select contratins in Alignments panel tree display). |
| 7.0.01.0 | Softree Opt. | Show actual volume in pits dialog box (if solution exists). |
| 7.0.06.0 | Survey | ASCII format (*.IPD) added for iPad Survey App (beta). |
| 7.0.10.0 | All | Added warning when you open a file saved from version 8.0 or greater. |
|
Version |
Module |
Description |
| 6.1.00.2 | Terrain | Insert File crash: when "all supported " extension list too long |
| 6.1.00.2 | Location | Stripping missing if applied only to one side |
| 6.1.00.2 | Softree Opt | Catch non-increasing haul costs in ground edit dialog box |
| 6.1.00.2 | Softree Opt | General options tab: make changes to description or vertical range (or other) then move the Accuracy slider, lose changes |
| 6.1.00.2 | Softree Opt | Set Current curve conversion bug: "curve too big to fit tangents" - intermittent |
| 6.1.00.2 | Location | Import land xml not working with overturns in cross sections. |
| 6.1.01.0 | All | Alaska state plane zone 1 origin wrong (negative northing values) - incorporated GDAL 1.10.0 to fix |
| 6.1.01.0 | Location | Add fixed sections outside of topo surface messes up all fixed cross sections |
| 6.1.01.0 | Location | Culverts drawn upsidedown if left length less than zero (culvert doesn't cross centerline) |
| 6.1.01.0 | Location | Import land xml not working with overturns in cross sections. |
| 6.1.01.0 | Location | new Location from a LandXML alignment (with cross sections), silently fails if the alignment falls off the OG Terrain |
| 6.1.01.0 | Terrain | DWG read bug: curves appear in the wrong place. |
| 6.1.01.0 | Terrain | TIF reads in all blue - possibly a non-standard image created by ESRI |
| 6.1.01.0 | Softree Opt | Adjust curve boundaries to honor min curve length (where possible). |
| 6.1.01.0 | Softree Opt | No warning if alignment does not include station of control point |
| 6.1.01.0 | Softree Opt | Spurious "Station ranges do not match" error |
| 6.1.01.0 | Location | Fixed Section Codes (new codes not in template) not displaying in Plan, Profile and Section |
| 6.1.01.1 | Location | Duplicate Codes appearing in Add Template Codes dialog |
| 6.1.01.1 | Location | Panels not updating after Module setup change (units, digits after decimal, etc.) |
| 6.1.01.1 | Softree Opt | Adjust stations of pits, control points and constraints with H. alignment |
| 6.1.01.1 | Softree Opt | Error handling: Out of memory crashes, other errors not reported properly |
| 6.1.01.1 | Softree Opt | Ground type add: haul costs set to zero |
| 6.1.01.1 | Softree Opt | No temp folders if turn off "export mass movement" |
| 6.1.01.1 | Softree Opt | Profile print and multi-plot: no display of optimal alignments |
| 6.1.01.1 | Softree Opt | Set document modified if Softree Optimal options etc. modifed |
| 6.1.01.1 | Softree Opt | Spurious error "Control point at station %f does not lie between two existing stations." |
| 6.1.01.1 | Softree Opt | Warning displayed for every iteration of convergence analysis |
| 6.1.01.1 | Softree Opt | Status area not updating properly |
| 6.1.02.1 | Terrain | LandXML: crash if read surface with no faces. |
| 6.1.02.1 | Softree Opt | "Problem too large" warning should not pop up for current alignment General options. |
| 6.1.02.1 | Softree Opt | Set Current: afterwards, current alignment cost uses the optimized profile, not the location profile |
| 6.1.02.1 | Softree Opt | Spurious error reports removed. Confusing error text improved. |
| 6.1.03.0 | Softree Opt | Crash drawing bitmap hatches if screen color depth set to 16bits. There is a possibility that an old bug has been re-introduced: incorrect hatch colors on print. |
| 6.1.03.0 | Terrain | Long feature names cause crash on save. |
| 6.1.03.2 | Terrain | Terrain plan crash on zoom in if unconnected multi-point feautres displayed (LiDAR for example). Also not all points displayed depending on zoom. 6.1.03.2 only. |
| 6.1.03.3 | Terrain | P-Line L-Line projection fails. This can cause hangs if the user tries to draw P-Line station features with custom dashed linetypes. |
| 6.1.03.4 | Location | Culvert ditch override taper zone incorrect. |
| 6.1.03.4 | Location | Mass haul volumes slightly incorrect when plan and profile points coincident. |
| 6.1.03.4 | Location | Terrain TOPO triangles out of date or missing: no warning when open Location design (if P-Line traverse exists). |
| 6.1.03.4 | Softree Opt | After long use, application draws incorrectly and eventually crashes. |
| 6.1.03.5 | Location | Speed Key Ctrl-F opens dialog box if Profile window current (should do auto balance on current section). |
| 6.1.03.5 | Softree Opt | Haul graph print fails. |
| 6.1.03.5 | Softree Opt | Import old GND file - get garbage costs. |
| 6.1.03.5 | Softree Opt | Better error messages required. |
| 6.1.03.5 | Softree Opt | Crash if close Alignments panel with items displayed in Profile window. |
| 6.1.03.5 | Softree Opt | Haul costs for current alignment not up-to-date on file open. |
| 6.1.04.1 | All | Using second monitor, dialog boxes often pop up in main monitor. |
| 6.1.04.2 | Terrain | KML read more than one file (sequential or together) -> crash. |
| 6.1.04.2 | Softree Opt | Control points, using existing alignment leads to inconsistent values. |
| 6.1.04.2 | Softree Opt | Special, Earth movement direction constraint not working properly. |
| 6.1.04.2 | Softree Opt | Ground Types, Movement costs some edit boxes should not be enabled. |
| 6.1.04.2 | Softree Opt | On cancel, error message should read "cancelled" not "failed". |
| 6.1.04.2 | Softree Opt | Recalc cost on open should only happen if there is something to recalculate. Can cause software to hang. |
| 6.1.04.2 | Softree Opt | Re-cost current -> optimal gets out of date so comparison fails. |
| 6.1.04.2 | Softree Opt | Set Current -> optimal gets set out of date. |
| 6.1.04.2 | Softree Opt | Set mass haul distances error (ground types dlg, prompt after set haul costs): if one or more distances undefined, should set values to something other than 0.0. The distances must be increasing in the Mass Haul options dialog box. |
| 6.1.04.2 | Softree Opt | Update BW assignment not working for re-cost? Need to re-calc MassHaul object. |
| 6.1.04.3 | Softree Opt | Costs not stable due to point selection issues |
| 6.1.04.3 | Softree Opt | Items out of date that shouldn't be. |
| 6.1.04.3 | Softree Opt | Automatic assign borrow/waste puts multiple items at same station and description too long. |
| 6.1.04.3 | Softree Opt | Set current shoulld update station range. |
| 6.1.04.3 | Softree Opt | Too many warning popups. Compound last three warning popups into one final one. |
| 6.1.04.3 | Softree Opt | Recalc cost on open should only happen if there is something to recalculate and the Alignments panel is open. |
| 6.1.04.4 | Location | LandXML Vertical alignment starts outside station range of Horizontal alignment. Unable to import Vertical alignment. |
| 6.1.04.4 | Location | Stripping issues fixed. |
| 6.1.04.4 | Softree Opt | Horizontal alignment modification: doesn't update all optimization options stations. |
| 6.1.04.4 | Softree Opt | Horizontal alignment modification Undo: doesn't restore optimization options stations. |
| 6.1.04.5 | All | 3D Window, print, export to image and Multi-Plot not working. |
| 6.1.04.5 | All | 3D Window, out of memory displaying large models. |
| 6.1.04.5 | Location | LandXML import alignment - does not set design speed or super elevaytion on horizontal curves - use the default from the template table. |
| 6.1.04.5 | Softree Opt | New optimal alignment: simplify new name. |
| 6.1.04.5 | Softree Opt | Tangent Insertion mode: some tangents replaced by curves with very large K. |
| 6.1.04.5 | Softree Opt | Spurious errors removed. |
| 6.1.04.5 | Softree Opt | Pits and Control points: remove dynamic elevation (dependant on current alignment). |
| 6.1.04.5 | Softree Opt | Recost accurate hangs if alignment falls off model (even with bridge assigned). |
| 6.1.04.5 | Softree Opt | Re-cost current alignment, unnecessary re-calculation. |
| 6.1.04.5 | Softree Opt | Re-cost current alignment, should not take place when opening a Location design with no optimization panel. |
| 6.1.04.6 | Location | LandXML alignment: can't read vertical if extends beyond horizontal. |
| 6.1.04.6 | Location | LandXML horizontal curve import fails if curve delta >= 180 |
| 6.1.04.6 | Location | Mouse edit of Horizontal IP not possible when IP is far from curve and close to another section of road. |
| 6.1.04.6 | Location | Stripping below layer 1 (near center line on steep side hill) |
| 6.1.04.6 | Location | Slope in ratio mode, tooltip for template leg slope is displayed as % or ratio, but % symbol is always displayed. |
| 6.1.04.6 | Terrain | 3d window: drape image shows stiching lines at tile boundaries. |
| 6.1.04.6 | Softree Opt | Colors wrong when printing optimal haul graph (text same color as last drawn optimal profile) |
| 6.1.04.6 | Softree Opt | Large symbols on optimal haul graph misleading. |
| 6.1.04.6 | Softree Opt | Spurious re-cost on screen layout read even if Alignment Panel was already up. |
| 6.1.04.6 | Softree Opt | "Encountered improper argument" error mousing over profile window (tooltip bug). |
| 6.1.04.8 | Location | Export to Terrain, any panel updates repeatedly (like 1000's of times). |
| 6.1.04.8 | Terrain | Comments (survey) label missing from radial shot after Survey Notes file import. |
| 6.1.04.8 | Terrain | Open DGN file crashes Terrain. |
| 6.1.04.8 |
Terrain/ Location |
Crash on touch screen devices closing last panel window (also can happen on file open, new and retrieve screen layout) |
| 6.1.04.8 | Softree Opt | Control points: change display so that elevation tolerance is clear when compined with vertical band. |
| 6.1.04.8 | Softree Opt | Control points: grade not shown if elevation not defined. |
| 6.1.04.8 | Softree Opt | Force pre-process on all optimal alignments after Set Current. |
| 6.1.04.8 | Softree Opt | No error if user creates station range bigger than actual alignmnet. Causes "Control point outside of band" error. |
| 6.1.04.8 | Softree Opt | Help for Haul Cost Edit dialog: missing images. |
| 6.1.04.9 | Location | Profile output rescale not working for export to DWG single wide page (not sampled often enough). |
| 6.1.04.9 | Survey | Crash on open extended side shot editor (only on some devices). |
| 6.1.04.9 | Terrain | Can't edit when measure mode is pending in Profile (plan works OK). |
| 6.1.05.0 | Softree Opt | Station range not right after alignment truncated. |
| 6.1.05.0 | Softree Opt | Progress box on wrong screeen sometimes. |
| 6.1.05.0 | Softree Opt | Multiple spurious warning for constraint exceded (for example minimum fill). |
| 6.1.06.0 | Location | Ground Type editor: embankment cost getting set to zero on multiple select |
| 6.1.06.0 | Location | Tree lists (template editor and optimization control dlg COptControlDlg) have items that look like links when you mouse over (but the links don't work) |
| 6.1.06.0 | Softree Opt | Arbitrary curve constraint removed. Some back-to-back curve solutions may not have been optimal. |
| 6.1.06.0 | Softree Opt | Error messages sometimes not clear. Work is ongoing on this front. |
| 6.1.06.0 | Softree Opt | Selected alignment profile doesn't always draw correctly (especially if there are some curves and some simple VIP points) |
| 6.1.06.0 | Softree Opt | Set current should prompt to merge or replace if not full range (default to merge) |
| 6.1.06.0 | Softree Opt | Simple or Forestry costing: Optimal Haul graph shows same material going both ways. |
| 6.1.06.0 | Softree Opt | Various user interface fixes. |
| 6.1.06.1 | All | Ground types editor (other places too) ratio not updated when change slope percent. |
| 6.1.06.2 | Softree Opt | Default borrow pit: no preference for cheaper cut material. |
| 6.1.06.2 | Softree Opt | New vertical alignment, copy current alignment into Profile. |
| 6.1.06.2 | Softree Opt | Open old file or read old RoadEng.gnd, costs should default to something reasonable (read out of Normal.gdx). |
| 6.1.06.2 | Softree Opt | New location design: default K factors set to 0.0 |
| 6.1.06.3 | Softree Opt | Costs wrong for simplified model (embankment cost set to the excavation cost). |
| 6.1.06.4 | Terrain | Always get 10 digits after decimal in display of distance values in Status and Points windows (probably elsewhere too) |
| 6.1.06.4 | Softree Opt | Add Control point: start/end should refer to station range of optimization (not horizontal alignment) |
| 6.1.06.4 | Softree Opt | Change of alignment, options, should set the Pre-Process check box. Change of discretization or range should force Pre-Process. |
| 6.1.06.4 | Softree Opt | Composite material should not be allowed for borrow pit. |
| 6.1.06.4 | Softree Opt | Cost wrong: for active alignment after modify from optimal, if calculated as current (uses optimized profile, which is still displayed) |
| 6.1.06.4 | Softree Opt | Display when not selected flag should default OFF for new files and opeing old files (pre 6.1.06.4) |
| 6.1.06.4 | Softree Opt | new alignment, doesn't change name |
| 6.1.06.4 | Softree Opt | new alignment, gets wrong profile sometimes (always current) |
| 6.1.06.4 | Softree Opt | optimized alignments break the grade range constraints (Standards tab). |
| 6.1.06.4 | Softree Opt | Overflow/underflow: report warning and volume after re-cost |
| 6.1.06.4 | Softree Opt | Overflow/underflow: separate items in panel list |
| 6.1.06.4 | Softree Opt | recost discretization copied into optimization options |
| 6.1.06.4 | Softree Opt | profile truncated incorrectly near end if in curve. |
| 6.1.06.4 | Softree Opt | spurious warning on re-cost all: "The discretization may be too coarse…" |
| 6.1.06.5 | Location | Various crashes caused by running out of memory for large Location designs (6.1.06.1-6.1.06.5 only) |
| 6.1.06.5 | Softree Opt | Control point add: select start or end, for partial optimization, station resets to start/end of horizontal alignment. |
| 6.1.06.5 | Softree Opt | After Set Current, costs always out of date. |
| 6.1.06.5 | Softree Opt | Allow set current for empty profile. |
| 6.1.06.5 | Softree Opt | If re-cost spacing changed, need to recalculate all (or volumes and mass haul out of date) |
| 6.1.06.6 | Softree Opt | Optimize cost (and optimal haul) calculation wrong for current alignment. OK after manual re-cost. |
| 6.1.06.7 | Terrain | Volume calculation crashes. "...improper argument..." error message. |
| 6.1.06.8 | Terrain | Mode toolbar image not right. |
| 6.1.06.9 | Terrain | Grading dialogue box, drop down for background Terrains too small. |
| 6.1.06.9 | Softree Opt | Costs out of date right after re-cost if spacing is changed. |
| 6.1.06.9 | Softree Opt | No error report on solver failed (log is OK). |
| 6.1.06.9 | Softree Opt | Options General tab: when Station Range All is unchecked, try to change the From value, the cursor jumps (type 45 get 54.000). |
| 6.1.06.9 | Softree Opt | Options General and Standards tabs: Invalid Field error pops up when typing. |
| 6.1.06.9 | Softree Opt | Separate logs for cost and optimize (so re-cost doesn't write over optimization log) |
| 6.1.06.9 | Softree Opt | Variable curves and tangents: user control for curve base length |
| 6.1.06.9 | Softree Opt | Various help and error message updates. |
| 6.1.07.0 | All | Grid (axis) labels not centered when read old file/screen layout (and grid lines off). |
| 6.1.07.0 | Location | New horizontal alignment points: elevations wrong; should be on ground (6.1.07.0 only). |
| 6.1.07.0 | Softree Opt | Alignment panel: text area not always big enough - need scroll bar. |
| 6.1.07.0 | Softree Opt | Special constraints: help doesn't always work with F1 key. |
| 6.1.07.0 | Softree Opt | Vertical band displayed incorrectly. |
| 6.1.07.2 | Terrain | Plan Options, Surface, Tin Shading options: AutoGen now merges with existing instead of deleting existing. Plus prevent bad ranges. |
| 6.1.07.2 | Softree Opt | Duplicate text (multiple saves) appears in TR1 or DS2 file after save to network. Rare, intermittent. |
| 6.1.07.2 | Softree Opt | Direction constraint, garbage text in ranges list. |
| 6.1.07.2 | Softree Opt | Crash when open older design while updating 3d display lists. |
| 6.1.07.2 | Softree Opt | Should be no need for pre-process after full feasibility check. |
| 6.1.07.2 | Softree Opt | Conflict detection improved, errors fixed. |
| 6.1.07.2 | Softree Opt | Process dialog changed to include feasibilty and two alignment options. Right click menu re-organized too. |
| 7.0.00.0 | Location | H Curves button missing from windows tool bar. |
| 7.0.00.0 | Location | OB not in available list for Mass Haul material selection. |
| 7.0.00.0 | Terrain | Merge Terrain: stray destination feature left over after merge. |
| 7.0.00.0 | Terrain | Select by boundary misses a feature if "retain selected features" checked. |
| 7.0.00.0 | Softree Opt | Borrow pit material wrong if choose any material after composite in table. |
| 7.0.00.0 | Softree Opt | Pits dialogue box: re-arrange and change some terminology. |
| 7.0.00.0 | Softree Opt | Prompt to re-calc all after pits modification in current alignment options. |
| 7.0.00.0 | Softree Opt | Optimization control dialogue box: constraints hard/soft indicator wrong sometimes. |
| 7.0.00.0 | Softree Opt | Volumes error (usually small) in re-cost for long roads with multiple mataerial. |
| 7.0.00.1 | Location | Move last vertical alignment point, get "Horizontal alignment does not contain all points - Vertical alignment may be removed.", then last VIP is removed and the horizontal alignment is shortened. |
| 7.0.00.1 | Location, Terrain | Multi-Plot Legend Options, Items dialog box font on text in list too small.. |
| 7.0.00.1 | Location, Terrain | Report Point Properties list and Terrain surface shading list: font too large (small too sometimes) for line spacing (Laptop with high res screen). |
| 7.0.00.2 | Terrain | 3D window: Not redrawing selected ftrs correctly. |
| 7.0.00.2 | Softree Opt | change "discretization" -> "sampling" (dialog boxes, help and tree list) |
| 7.0.00.2 | Softree Opt | error on update menu for Multi-plot: "Record has too many characters. Check that the end of record delimiter is specified correctly (i.e. \n instead of \n\r)." (depends on contents of clipboard) |
| 7.0.00.2 | Softree Opt | Optimal Haul graphic not visible of no Alignments panel |
| 7.0.00.2 | Softree Opt | Optimal Haul Table output: hard to understand |
| 7.0.00.2 | Softree Opt | Options dialog, General tab, uncheck all, try to change the Start/End for the optimization range, we get this annoying cursor issue where it sets itself at the front after typing the first number |
| 7.0.00.2 | Softree Opt | Sidecast with optimization that is subset of the length of the road -> crashing |
| 7.0.00.2 | Softree Opt | Undo Set Current doesn't redraw alignment list correctly (shows two current alignments) |
| 7.0.00.2 | Location | Profile sub-windows not working - anything after Mass Haul or Optimal Haul is blank (since version 7.0.00.1). |
| 7.0.00.3 | Location/Terrain | Multi-Plot Legend Options, Items dialog: items ALL black after any action by user. (since version 7.0.00.2). |
| 7.0.00.3 | Location/Terrain | Multi-Plot sub-view options: locking drop down not big enough. |
| 7.0.00.3 | Terrain | Merge TIN: change default hull offset to 0.01 (from 0.001). Small hull offset sometimes causes crossing hull-s and hull-d breaklines. |
| 7.0.00.3 | Terrain | Import GPX, GML, MapInfo fails. |
| 7.0.00.4 | Location | Save-As Google earth crash. Remove from release until fixed. |
| 7.0.00.4 | Location | Optimal Haul graphic: sidecast hover tip (tooltip) crash. |
| 7.0.00.5 | All | Change so that screen layouts that have just been installed will "enable all permitted", instead of doing nothing. |
| 7.0.00.5 | Location/Terrain | 3D window, large model: long pauses, sometimes with hourglass, during simple operations. |
| 7.0.00.6 | All | Samples and tutorial files get mixed up with version 6 installs; append "70" on new folders. |
| 7.0.00.6 | Location | Export Multi-Plot to DWG with start page > 1 generates one or more junk DWG files with page number less than start page. |
| 7.0.00.7 | All | License not Found wizard: I would like to purchace button -> bad link. |
| 7.0.00.7 | All | Some samples require Softree Optimal function group for no reason. |
| 7.0.00.7 | Location | Fixed section window docked in panel: can't see top right buttons unless widen panel. |
| 7.0.00.9 | All | 3D window: cancel out of some non-3d functions (move size?) -> extents undefined -> no 3D display. |
| 7.0.00.9 | All | 3D window: Large mem leak and error message box (mem alloc failed) sometimes. |
| 7.0.00.9 | All | 3D window: user selected explicit re-build -> no TIN rebuild (sometimes). |
| 7.0.00.9 | All | Digits after decimal < 0 will cause problems . |
| 7.0.00.9 | All | Multi-Plot Legend, can't turn off bounding rectangle. |
| 7.0.00.9 | Install | Old version 6 Survey_Map shortcut remains on desktop after install. |
| 7.0.00.9 | Location | Bad template component in Library: RoadWay/Lane applies super twice. |
| 7.0.00.9 | Location | Wrong digits after decimal (decimals) for grades. |
| 7.0.00.9 | Location, Survey | Open ground table fails if extension not upper case (gdx fails, GDX OK). |
| 7.0.00.9 | Location, Terrain | Multi-Plot, image sub-views: if border is visible, it is always rounded with radius 4mm (after file or screen layout open). |
| 7.0.00.9 | Terrain | Simplify always removes all but first and last point for closed features. |
| 7.0.00.9 | Terrain | Move/Size/Rotate: sometimes only rotate cursor available if the bulk of the selected rectangle is off the screen (zoomed in). Fix by setting maximum rotate border size. |
| 7.0.00.9 | Terrain | Move/Size/Rotate: sometimes only move cursor available if the border of the selected rectangle is off the screen (zoomed in). Fix by switching to rotate mode with the Ctrl key. |
| 7.0.00.9 | V.Opt | Control points elevation and grade rounded. |
| 7.0.00.9 | V.Opt | Feasibility fails for no reason, rare.. |
| 7.0.00.9 | V.Opt | Optimized alignment doesn't meet grade specs, rare. |
| 7.0.00.9 | V.Opt | Options, General tab, sample spacing: can't type a decimal point first (no easy way to enter 0.5m spacing). |
| 7.0.00.9 | V.Opt | Options, General tab, Station Range: type ".." instantly turns into end station (this is only ok if enough digits after decimal). |
| 7.0.00.9 | V.Opt | Spurious warnings for PolyLine curves mode (station 0.0 is the first station): "WARNING- No maximum grade break (sag) for line starting at station 0.00." and "WARNING- No maximum grade break (crest) for line starting at station 0.00.". |
| 7.0.00.9 | V.Opt | Various Help file updates. |
| 7.0.01.0 | Location | Hang on select last Fixed Section or on open design; rare. |
| 7.0.01.0 | Location | Horizontal curve panel: Arc Length should be Distance accuracy (digits after decimal), not Directions. |
| 7.0.01.0 | Location | Profile Areas graphic sub-window not working properly with Fixed Cross Sections. |
| 7.0.01.0 | Location | Spurious re-cost and optimal haul calculation on open designs with no Alignment Properties Panel or Optimal Haul window. |
| 7.0.01.0 | Terrain | Tool bar Mode Tools wrong height (too tall). |
| 7.0.01.0 | V.Opt | Ground table with composite materials not readable by older version 7 applications. |
| 7.0.01.0 | V.Opt | Design with fixed cross sections hangs on open or hangs when jump to last fixed section. Rare. |
| 7.0.01.1 | V.Opt | Re-Cost with standards check crash. Only if Options-Standards Min. Tangent grade (%) is violated. |
| 7.0.01.2 | Location | Decimals on P-line survey stations not adjustable (always 1). |
| 7.0.01.2 | Location | Export large alignment sections to LandXML causes crash. |
| 7.0.01.2 | Location | Ground line in cross sections wrong (all the same) occurs in P-Line only design where at least one P-Line cross section does not cross the L-Line. Rare. |
| 7.0.01.2 | Terrain | 3D Window Plan Drape no warning if number of tiles is huge. |
| 7.0.01.2 | V.Opt | Quick profile should report constraint violations to log if constraint is softened. |
| 7.0.01.2 | V.Opt | Feasibility is writing the standards and control points violations for the hidden profile it creates, it should not. . |
| 7.0.01.2 | V.Opt | Feasibility passes if constraint is softened but there is no indication that constraint is softened (and that the design is really still infeasible) . |
| 7.0.01.2 | V.Opt | Some projects fail to optimimize with no explanation (caused by numerical instability). |
| 7.0.02.0B | V.Opt | Constraint ranges: auto-generate crashes (7.0.02.0B only ). |
| 7.0.02.0B | V.Opt | Export Optimal Haul to clipboard: costs summary heading not right "direction" should read "haul" |
| 7.0.02.0B | V.Opt | Optimal Haul hover tip (tooltip) not right (imperial units only): shows different flow values for "All" and sum of components (All is less than sum ). |
| 7.0.02.0B | V.Opt | Optimal Haul hover tips: box not big enough for text, arrows, pit symbols don't always work (depends on font). Optimal Haul and Mass Haul, tips fall off edge of window. |
| 7.0.02.0B | V.Opt | Crash in conflict checker if control point grade exceeds standards. |
| 7.0.02.0B | V.Opt | Open older project with alignment Standards set to Curves and Tangents [slow] get bad options: Min Tangent Length value set to 0.0 (and disabled); and Process gives bad results. Work around by changing to/from another combo box selection (e.g. Curves [fast]). |
| 7.0.02.1 | V.Opt | Optimizer finds unbalanced solution because default pit is cheaper than cutting material from the roadway. 7.0.02.1 only; never released. |
| 7.0.03.0 | Location | Profile grid using font from Plan window |
| 7.0.03.0 | Terrain | Crash on save; rare, after deleting opne of multiple 3D windows. |
| 7.0.03.0 | V.Opt | Process dialogue box: disabled and inaccurate Hard/Soft radio buttons should be removed (now controlled in the Alignment panel tree context menu). |
| 7.0.04.0 | All | Multi-Plot: Spurious shuffle when select locked sub-view. |
| 7.0.04.0 | Terrain | Very slow DEM read (LiDAR data for example). |
| 7.0.04.0 | Terrain | Unable to disable section label. |
| 7.0.06.0 | Terrain | ASCII format (*.IPD) reader not reading last shot on the right. |
| 7.0.07.0 | V.Opt | Vertical band display for Full Bench constraint incorrect. |
| 7.0.07.1 | Survey/Map | "Invalid Argument" error saving and opening files in Survey/Map module on Windows 10. Intermittent. |
| 7.0.07.7 | Terrain | Not Geo-referencing SID and JP2 images correctly when a world file is not present. |
| 7.0.07.7 | Terrain | Not correctly rotating TIF and other images with world files in some situations. |
| 7.0.08.0 | Location | E-library: SubCut II - Under SG component not calculating fill volumes correctly when bIncludeInSG flag set. |
| 7.0.08.0 | Terrain | Insert image with different units (meters vs. feet), coordinate transformation incorrect. |